-
TWIN-MOTOR GEARBOX KIT
Specifications
- contains: 2 motors, 3 set gears, metal shafts, gear box and other accessories
- motor: 3 VDC / 12500 rpm
- gear ratio:
- 1:60: 200 rpm output
- 1:120: 100 rpm output
- 1:288: 42 rpm output
- power supply: 2 x 1.5 V AAA or 2 x 1.5 V AA (not incl.)
-
3 IN 1 ALL TERRAIN ROBOT
Specifications
- power supply: 4 x AA batteries (LR6C not incl.)
- weight: 425g
- number of pieces: 148
-
ROBOT FROG
Specifications
- dimensions: 90 x 125 x 100 mm / 3.5 x 4.9 x 3.9″
- power supply:
- mechanical: 2 x 1.5 V AA batteries (not incl.)
- electronic: 9 V battery (not incl.)
- number of pieces: 103
-
ULTRASONIC RADAR MODULE
Specifications
- range: 20 … 250cm
- frequency: 40kHz
- digital output: 5V (50mA max.)
- analogue output: 0…5V (5mA max)
- buzzer output: 12V (100mA max.)
- relay contacts: 1A low voltage NO/NC
- power supply: 12VDC
- current consumption: 200mA max.
- dimensions: 110 x 50 x 18mm / 4.3 x 2.0 x 0.7″
-
UNIVERSAL TIMER MODULE WITH USB INTERFACE
Specifications
- power supply: 12 VDC (100 mA max.)
- relay output: 8 A / 250 VAC max.
- minimum event time : 100 ms
- maximum event time: 1000 h (over 41 days)
- dimensions: 68 x 56 x 20 mm (2.6″ x 2.2″ x 0.8″)
-
STEREO AMPLIFIER MODULE 2 x 30W
Specifications
- music power output: 2 x 30W / 4ohm
- RMS output: 2 x 15Wrms / 4ohm or 2 x 10Wrms / 8ohm
- total harmonic distortion: 0.07% (1W / 1kHz)
- channel separation: 70dB
- frequency response: 7Hz to 60kHz (-3dB)
- signal-to-noise ratio: 98dB (A-weighted)
- input sensitivity: 300mV / 150Kohm
- transient suppression on/off switch
- overload and short-circuit protection: max. 1h
- supply voltage: 2 x 12Vac / 2A (50W transfo recommended)
- dimensions: 70 x 50mm
-
RECORDING AUDIO SHIELD FOR ARDUINO
Specifications
- audio sample frequency: 8 kHz
- uses pin 10 on an Arduino® UNO board as a Chip Select
- uses the ICSP pins on an Arduino as a serial connection to the shield to free up I/O pins
- memory write up to 100.000 X
- dimensions: 80 x 55 x 30 mm / 3.15 x 2.16 x 1.18″
-
ETHERNET RELAY CARD
Specifications
- 8 relay contacts: 12A @ 30Vdc or 16A @ 230Vac
- 1 input: dry contact or voltage input 5…20Vac or dc
- power supply: 12Vac or dc/500mA (option: TR-G3/8)
- diameter: 160 x 107mm
-
64 LED RGB MATRIX
Specifications
- WS2812S LEDs
- power supply: 5 VDC
- current consumption: 3,5 A / panel max.
- dimensions: 72 x 72 x 3 mm (2.8″ x 2.8″ x 0.1″)
- LED pitch: 9 mm (0,35″)
-
USB INTERFACE CARD
Specifications
- 5 digital inputs (0= ground, 1= open) (on-board test buttons provided)
- 2 analogue inputs with attenuation and amplification option (internal test +5V provided)
- 8 digital open collector output switches (max 50V/100mA) (on-board LED indication)
- 2 analogue outputs:
- 0 to 5V, output resistance 1K5
- PWM 0 to 100% open collector outputs max 100mA / 40V (on-board LED indication)
- general respons time: 2ms per command
- power supply: through USB approx. 70mA
- dimensions: 110 x 80mm / 4.3 x 3.2″
-
2-CHANNEL RF REMOTE CONTROL SET
Specifications
- receiver:
- power supply: 9 to 13Vac or 10 to 15Vdc
- consumption : 130mA max. / 20mA standby (heating off)
- relay contacts NO / NC: 5A (resistive load) each
- 433MHz operation
- selectable timers per output: 0.5s, 5s, 30s, 1min, 5min, 15min, 30min and 60min
- Heating option for use in cold environments
- open field range of up to 30m possible
- external antenna
- dimensions: 80 x 70 x25mm / 3.15 x 2.75 x 0.98″
- transmitter:
- power supply: 12V battery (included)
- V23GA: ALKALINE MN21 V23A 12V-38mAh 4223.101.401 (1pc/bl) / GP23GAC: ALKALINE V23A / EL12 12 V (5pcs/bl)
- 433MHz operation
- dimensions: 63 x 40 x 16mm (2.5″ x 1.6″ x 0.6″)
- power supply: 12V battery (included)
- receiver:
-
LED DIMMER WITH RF REMOTE CONTROL
Specifications
- power supply: 12-24VDC
- max. load: 6A
- LED PWM frequency: +/- 300Hz
- dimensions: +/- 80x70x23mm/3.1×2.8×0.9″
- remote:
- 433.92 MHz operation
- R&TTE compliant ( ETS 300-220)
- battery: 12V V23GA: ALKALINE MN21 V23A 12V-38mAh 4223.101.401 (1pc/bl) incl.
- dimensions: 63x40x16mm/2.5×1.6×0.6″
