Compare“Precision cutting set, with holders, blades, needles and sharpening stone, 53 pieces” has been added to the compare list
“Precision cutting set, with holders, blades, needles and sharpening stone, 53 pieces” was added to the compare list
-
Specifications
- servo motor connector shield (VRSSM):
- compatible with ARDUINO-UNO-R3: ARDUINO UNO REV.3 and ARD-A000067: ARDUINO MEGA2560 REV3 (required but not included!)
- ARDUINO-UNO-R3: ARDUINO UNO REV.3 can drive max. 12 servo motors
- ARD-A000067: ARDUINO MEGA2560 REV3 can drive max. 36 servo motors
- IR receiver
- beeper
- power indicator LEDs
- battery shield (VRBS1):
- power supply: 12 V booster for Arduino board (4 x AA batteries, alkaline or NiMH recommended but not incl.)
- ON-OFF switch
-
Specifications
- arm:
- arm and forearm length: 160 mm
- maximum arm height: 270 mm
- maximum height reached by the wrist: 310 mm
- maximum extension (clamp included): 400 mm
- arm rotation on support base: 180°
- base support dimensions: 145 x 145 mm
- operation: via 5 servos
- lifting capacity at the wrist: 250 g
- weight: 850 g
- gripper:
- maximum jaw opening: 65 mm
- jaw length: 45 mm
- large 55G servos:
- operating speed: 0.17 s / 60 degrees (at 4.8 V without load)
- operating speed: 0.13 s / 60 degrees (at 6 V without load)
- torque: 9.4 kg / cm (at 4.8 V)
- stall torque: 13 kg / cm (at 6 V)
- power supply: 4.8 to 6 V
- metal gears:
- dimensions: 40.7 x 19.7 x 42.9 mm
- weight: 55 g
- small 9G servos:
- operating speed: 0.12 s / 60 degrees (at 4.8 V without load)
- operating speed: 0.11 s / 60 degrees (at 6 V without load)
- torque: 1.2 kg / cm (at 4.8 V)
- torque: 1.5 kg / cm (at 6 V)
- power supply: 4.8 to 6 V
- plastic gears:
- dimensions: 22 x 12 x 29 mm
- weight: 9 g
-
Specifications
| Physical properties |
| Primary colour |
Yellow |
| Additional colours |
Black |
| Depth unit |
126 mm |
| Height unit |
165 mm |
| Width unit |
138 mm |
| Weight unit |
630 g |
| Material |
Plastic + PS/LED |
-
Specifications
| Physical properties |
| Primary colour |
Blue |
| Additional colours |
Yellow,Grey |
| Weight unit |
745 g |
| Material |
Plastic + PS/LED |
-
| Physical properties |
| Primary colour |
Multi |
| Weight unit |
420 g |
| Material |
Plastic + PS/LED |
-
Specifications
| Physical properties |
| Battery IEC size |
AA (LR6, R6, FR6, HR6, KR6, ZR6 ,15A, 15D, 15LF, 1.2H2, 1.2K2, UM3, Pencil, MN1500, MX1500, MV1500) |
| Primary colour |
Multi |
| Depth unit |
23 cm |
| Height unit |
5 cm |
| Width unit |
32.4 cm |
| Weight unit |
900 g |
| Electrical Properties |
| Battery voltage rating |
1.5 V |
-
Specifications
- contains: 2 motors, 3 set gears, metal shafts, gear box and other accessories
- motor: 3 VDC / 12500 rpm
- gear ratio:
- 1:60: 200 rpm output
- 1:120: 100 rpm output
- 1:288: 42 rpm output
- power supply: 2 x 1.5 V AAA or 2 x 1.5 V AA (not incl.)
-
Specifications
- power supply: 4 x AA batteries (LR6C not incl.)
- weight: 425g
- number of pieces: 148
-
Specifications
- dimensions: 90 x 125 x 100 mm / 3.5 x 4.9 x 3.9″
- power supply:
- mechanical: 2 x 1.5 V AA batteries (not incl.)
- electronic: 9 V battery (not incl.)
- number of pieces: 103
-
Specifications
- range: 20 … 250cm
- frequency: 40kHz
- digital output: 5V (50mA max.)
- analogue output: 0…5V (5mA max)
- buzzer output: 12V (100mA max.)
- relay contacts: 1A low voltage NO/NC
- power supply: 12VDC
- current consumption: 200mA max.
- dimensions: 110 x 50 x 18mm / 4.3 x 2.0 x 0.7″
-
Specifications
- power supply: 12 VDC (100 mA max.)
- relay output: 8 A / 250 VAC max.
- minimum event time : 100 ms
- maximum event time: 1000 h (over 41 days)
- dimensions: 68 x 56 x 20 mm (2.6″ x 2.2″ x 0.8″)
-
Specifications
- music power output: 2 x 30W / 4ohm
- RMS output: 2 x 15Wrms / 4ohm or 2 x 10Wrms / 8ohm
- total harmonic distortion: 0.07% (1W / 1kHz)
- channel separation: 70dB
- frequency response: 7Hz to 60kHz (-3dB)
- signal-to-noise ratio: 98dB (A-weighted)
- input sensitivity: 300mV / 150Kohm
- transient suppression on/off switch
- overload and short-circuit protection: max. 1h
- supply voltage: 2 x 12Vac / 2A (50W transfo recommended)
- dimensions: 70 x 50mm
