-
TWO LEGGED ALLBOT
Specifications
- servo motor connector shield (VRSSM):
- compatible with ARDUINO-UNO-R3: ARDUINO UNO REV.3 and ARD-A000067: ARDUINO MEGA2560 REV3 (required but not included!)
- ARDUINO-UNO-R3: ARDUINO UNO REV.3 can drive max. 12 servo motors
- ARD-A000067: ARDUINO MEGA2560 REV3 can drive max. 36 servo motors
- IR receiver
- beeper
- power indicator LEDs
- battery shield (VRBS1):
- power supply: 12 V booster for Arduino board (4 x AA batteries, alkaline or NiMH recommended but not incl.)
- ON-OFF switch
- servo motor connector shield (VRSSM):
-
Solar & Hydraulic Construction Kit 12 in 1
Specifications
Physical properties Primary colour Blue Additional colours Yellow,Grey Weight unit 745 g Material Plastic + PS/LED -
Electric Circuit Kits For Kids 8+
Specifications
Physical properties Battery IEC size AA (LR6, R6, FR6, HR6, KR6, ZR6 ,15A, 15D, 15LF, 1.2H2, 1.2K2, UM3, Pencil, MN1500, MX1500, MV1500) Primary colour Multi Depth unit 23 cm Height unit 5 cm Width unit 32.4 cm Weight unit 900 g Electrical Properties Battery voltage rating 1.5 V -
TWIN-MOTOR GEARBOX KIT
Specifications
- contains: 2 motors, 3 set gears, metal shafts, gear box and other accessories
- motor: 3 VDC / 12500 rpm
- gear ratio:
- 1:60: 200 rpm output
- 1:120: 100 rpm output
- 1:288: 42 rpm output
- power supply: 2 x 1.5 V AAA or 2 x 1.5 V AA (not incl.)
-
3 IN 1 ALL TERRAIN ROBOT
Specifications
- power supply: 4 x AA batteries (LR6C not incl.)
- weight: 425g
- number of pieces: 148
-
ROBOT FROG
Specifications
- dimensions: 90 x 125 x 100 mm / 3.5 x 4.9 x 3.9″
- power supply:
- mechanical: 2 x 1.5 V AA batteries (not incl.)
- electronic: 9 V battery (not incl.)
- number of pieces: 103
-
ULTRASONIC RADAR MODULE
Specifications
- range: 20 … 250cm
- frequency: 40kHz
- digital output: 5V (50mA max.)
- analogue output: 0…5V (5mA max)
- buzzer output: 12V (100mA max.)
- relay contacts: 1A low voltage NO/NC
- power supply: 12VDC
- current consumption: 200mA max.
- dimensions: 110 x 50 x 18mm / 4.3 x 2.0 x 0.7″
-
UNIVERSAL TIMER MODULE WITH USB INTERFACE
Specifications
- power supply: 12 VDC (100 mA max.)
- relay output: 8 A / 250 VAC max.
- minimum event time : 100 ms
- maximum event time: 1000 h (over 41 days)
- dimensions: 68 x 56 x 20 mm (2.6″ x 2.2″ x 0.8″)
-
RECORDING AUDIO SHIELD FOR ARDUINO
Specifications
- audio sample frequency: 8 kHz
- uses pin 10 on an Arduino® UNO board as a Chip Select
- uses the ICSP pins on an Arduino as a serial connection to the shield to free up I/O pins
- memory write up to 100.000 X
- dimensions: 80 x 55 x 30 mm / 3.15 x 2.16 x 1.18″
-
ETHERNET RELAY CARD
Specifications
- 8 relay contacts: 12A @ 30Vdc or 16A @ 230Vac
- 1 input: dry contact or voltage input 5…20Vac or dc
- power supply: 12Vac or dc/500mA (option: TR-G3/8)
- diameter: 160 x 107mm
-
64 LED RGB MATRIX
Specifications
- WS2812S LEDs
- power supply: 5 VDC
- current consumption: 3,5 A / panel max.
- dimensions: 72 x 72 x 3 mm (2.8″ x 2.8″ x 0.1″)
- LED pitch: 9 mm (0,35″)
-
USB INTERFACE CARD
Specifications
- 5 digital inputs (0= ground, 1= open) (on-board test buttons provided)
- 2 analogue inputs with attenuation and amplification option (internal test +5V provided)
- 8 digital open collector output switches (max 50V/100mA) (on-board LED indication)
- 2 analogue outputs:
- 0 to 5V, output resistance 1K5
- PWM 0 to 100% open collector outputs max 100mA / 40V (on-board LED indication)
- general respons time: 2ms per command
- power supply: through USB approx. 70mA
- dimensions: 110 x 80mm / 4.3 x 3.2″
