“1.75 mm (1/16") PLA FILAMENT - PINK - 1 kg / 2.2 lb” was added to the compare list
-
Specifications
- servo motor connector shield (VRSSM):
- compatible with ARDUINO-UNO-R3: ARDUINO UNO REV.3 and ARD-A000067: ARDUINO MEGA2560 REV3 (required but not included!)
- ARDUINO-UNO-R3: ARDUINO UNO REV.3 can drive max. 12 servo motors
- ARD-A000067: ARDUINO MEGA2560 REV3 can drive max. 36 servo motors
- IR receiver
- beeper
- power indicator LEDs
- battery shield (VRBS1):
- power supply: 12 V booster for Arduino board (4 x AA batteries, alkaline or NiMH recommended but not incl.)
- ON-OFF switch
-
Specifications
- arm:
- arm and forearm length: 160 mm
- maximum arm height: 270 mm
- maximum height reached by the wrist: 310 mm
- maximum extension (clamp included): 400 mm
- arm rotation on support base: 180°
- base support dimensions: 145 x 145 mm
- operation: via 5 servos
- lifting capacity at the wrist: 250 g
- weight: 850 g
- gripper:
- maximum jaw opening: 65 mm
- jaw length: 45 mm
- large 55G servos:
- operating speed: 0.17 s / 60 degrees (at 4.8 V without load)
- operating speed: 0.13 s / 60 degrees (at 6 V without load)
- torque: 9.4 kg / cm (at 4.8 V)
- stall torque: 13 kg / cm (at 6 V)
- power supply: 4.8 to 6 V
- metal gears:
- dimensions: 40.7 x 19.7 x 42.9 mm
- weight: 55 g
- small 9G servos:
- operating speed: 0.12 s / 60 degrees (at 4.8 V without load)
- operating speed: 0.11 s / 60 degrees (at 6 V without load)
- torque: 1.2 kg / cm (at 4.8 V)
- torque: 1.5 kg / cm (at 6 V)
- power supply: 4.8 to 6 V
- plastic gears:
- dimensions: 22 x 12 x 29 mm
- weight: 9 g
-
Specifications
| Physical properties |
| Primary colour |
Yellow |
| Additional colours |
Black |
| Depth unit |
126 mm |
| Height unit |
165 mm |
| Width unit |
138 mm |
| Weight unit |
630 g |
| Material |
Plastic + PS/LED |
-
Specifications
| Physical properties |
| Primary colour |
Blue |
| Additional colours |
Yellow,Grey |
| Weight unit |
745 g |
| Material |
Plastic + PS/LED |
-
| Physical properties |
| Primary colour |
Multi |
| Weight unit |
420 g |
| Material |
Plastic + PS/LED |
-
Specifications
| Physical properties |
| Battery IEC size |
AA (LR6, R6, FR6, HR6, KR6, ZR6 ,15A, 15D, 15LF, 1.2H2, 1.2K2, UM3, Pencil, MN1500, MX1500, MV1500) |
| Primary colour |
Multi |
| Depth unit |
23 cm |
| Height unit |
5 cm |
| Width unit |
32.4 cm |
| Weight unit |
900 g |
| Electrical Properties |
| Battery voltage rating |
1.5 V |
-
Specifications
- contains: 2 motors, 3 set gears, metal shafts, gear box and other accessories
- motor: 3 VDC / 12500 rpm
- gear ratio:
- 1:60: 200 rpm output
- 1:120: 100 rpm output
- 1:288: 42 rpm output
- power supply: 2 x 1.5 V AAA or 2 x 1.5 V AA (not incl.)
-
Specifications
- power supply: 4 x AA batteries (LR6C not incl.)
- weight: 425g
- number of pieces: 148
-
Specifications
- dimensions: 90 x 125 x 100 mm / 3.5 x 4.9 x 3.9″
- power supply:
- mechanical: 2 x 1.5 V AA batteries (not incl.)
- electronic: 9 V battery (not incl.)
- number of pieces: 103
-
Specifications
- range: 20 … 250cm
- frequency: 40kHz
- digital output: 5V (50mA max.)
- analogue output: 0…5V (5mA max)
- buzzer output: 12V (100mA max.)
- relay contacts: 1A low voltage NO/NC
- power supply: 12VDC
- current consumption: 200mA max.
- dimensions: 110 x 50 x 18mm / 4.3 x 2.0 x 0.7″
-
Specifications
- power supply: 12 VDC (100 mA max.)
- relay output: 8 A / 250 VAC max.
- minimum event time : 100 ms
- maximum event time: 1000 h (over 41 days)
- dimensions: 68 x 56 x 20 mm (2.6″ x 2.2″ x 0.8″)
-
Specifications
- music power output: 2 x 30W / 4ohm
- RMS output: 2 x 15Wrms / 4ohm or 2 x 10Wrms / 8ohm
- total harmonic distortion: 0.07% (1W / 1kHz)
- channel separation: 70dB
- frequency response: 7Hz to 60kHz (-3dB)
- signal-to-noise ratio: 98dB (A-weighted)
- input sensitivity: 300mV / 150Kohm
- transient suppression on/off switch
- overload and short-circuit protection: max. 1h
- supply voltage: 2 x 12Vac / 2A (50W transfo recommended)
- dimensions: 70 x 50mm
