Specifications
experiment module can be powered via USB
power output to target is supported
indicator LEDs for power supply and programming mode
dimensions:
programming and learning module: 90 x 74 mm / 3.54 x 2.91″
programmer only: 34 x 74 mm / 1.34 x 2.91″
Specifications
breadboard dimensions: 80 x 60mm / 3.15″ x 2.36″
Specifications
high contrast LCD: 64 x 128 pixels with white LED backlight
maximum sample rate: 1MS/s for repetitive signals, 100kS/s in real time
input amplifier bandwidth: 200kHz (-3 dB)
measurements can be performed up to: 100kHz
input impedance: 100kohm // 20pF
maximum input voltage: 30Vpeak (AC + DC)
input coupling: DC and AC
AD resolution: 8 bits
run modes: run, single
trigger level adjustable: in 16 steps
timebase range: in 15 steps, 10µs/division to 500ms/division
input sensitivity range: in 6 steps, 100mV/division to 5V/division
test output: 1.95kHz / 3.3Vpp
full auto set up for: Volt/div and time/div (or manual)
sensitivity down to 10mV
readouts: DC, AC+DC, true RMS, dBm, Vpp, min. & max.
time and voltage markers readout
frequency readout (through markers)
battery operated: 4 x AAA batteries (max. 100mA)
power save mode
dimensions: 80 x 115 x 40 mm / 3.14 x 4.52 x 1.57″
weight: 190g (6.70 oz) with batteries
Specifications
breadboard dimensions: 80 x 60mm / 3.15″ x 2.36″
Specifications
data rates up to 10 Mbps
integrated MAC controller
8 kB Transmit / Receive Packet Dual Port Buffer
the MAC controller supports both Unicast, Multicast and Broadcast packets, has a programmable (up to 64-byte) pattern matching feature within a packet at user defined offset and programmable wake-up on multiple packet formats (Magic Packet, Unicast, Multicast, Broadcast, specific packet match or any packet)
uses pin 10 and 2 on an Arduino UNO™ board. It also uses the ICSP connector as a serial connection to the shield to free up I/O pins
dimensions: 68 x 53mm / 2.67 x 2.08″
Specifications
range: -20° ~ +70°C
output: 0 ~ 20mA current loop
output voltage compliance: 10V
accuracy: 2° full range
one single adjustment
3-wire system: GND, +V and OUT
power supply: 12VDC for 0 ~ 5V OUT / 15VDC for 0 ~ 10V OUT
current consumption: 30mA max.
dimensions: 55 x 35 x 15mm / 2.2 x 1.4 x 0.6″
Specifications
power supply: 12V DC
consumption: max. 4A
outputs: 12V DC / 400mA per channel (total : max 4A)
dimensions: 140 x 100 x 27mm / 5.5 x 3.9 x 1.1″
Specifications
power output: 750 mA continuous, (1 A peak)
wide range AC – power input: 5 … 30 V
5 dry-contact inputs
1 logic open collector output
power supply: 10 … 30 VAC
dimensions: 117 x 65.5 x 25 mm / 4.6 x 2.58 x 0.98″
Specifications
power supply for relays: 9-10Vac or 12 to 14Vdc (500mA), example: PS1205
8 high-power relays: 16A each (resistive load)
dimensions: 160 x 107 x 30mm / 6.3 x 4.2 x 1.2″
Specifications
15 open collector outputs: 50V / 100mA
LED indication for every output
change-over or pulse contact: selectable per output
power supply: 8 – 14VDC or 2 x 12VAC / 150mA
PCB dimensions: 70 x 145mm (2.8″ x 5.7″)
recommended housing: WCAH2851: PLASTIC BOX – BLACK 160 x 95 x 55 mm
recommended transformer: 2120038M
recommended adapter: PS1205
Specifications
max. load: 2A (4A with heat sink)
supply voltage: 220VAC 50/60Hz (110VAC possible)
transmitter / receiver distance: max. 7m (23′)
not suitable for halogen lights
Specifications
transmitter / receiver range: up to 9m (29.5′)
relay output: 240V / 5A (switch or pulse contact)
supply voltage: 220VAC (110VAC possible)
recommended housing: B6713
