-
USB PIC PROGRAMMER AND TUTOR BOARD
Specifications
- experiment module can be powered via USB
- power output to target is supported
- indicator LEDs for power supply and programming mode
- dimensions:
- programming and learning module: 90 x 74 mm / 3.54 x 2.91″
- programmer only: 34 x 74 mm / 1.34 x 2.91″
-
SOLAR ENERGY EXPERIMENT KIT
Specifications
- breadboard dimensions: 80 x 60mm / 3.15″ x 2.36″
-
EDUCATIONAL LCD OSCILLOSCOPE
Specifications
- high contrast LCD: 64 x 128 pixels with white LED backlight
- maximum sample rate: 1MS/s for repetitive signals, 100kS/s in real time
- input amplifier bandwidth: 200kHz (-3 dB)
- measurements can be performed up to: 100kHz
- input impedance: 100kohm // 20pF
- maximum input voltage: 30Vpeak (AC + DC)
- input coupling: DC and AC
- AD resolution: 8 bits
- run modes: run, single
- trigger level adjustable: in 16 steps
- timebase range: in 15 steps, 10µs/division to 500ms/division
- input sensitivity range: in 6 steps, 100mV/division to 5V/division
- test output: 1.95kHz / 3.3Vpp
- full auto set up for: Volt/div and time/div (or manual)
- sensitivity down to 10mV
- readouts: DC, AC+DC, true RMS, dBm, Vpp, min. & max.
- time and voltage markers readout
- frequency readout (through markers)
- battery operated: 4 x AAA batteries (max. 100mA)
- power save mode
- dimensions: 80 x 115 x 40 mm / 3.14 x 4.52 x 1.57″
- weight: 190g (6.70 oz) with batteries
-
SOLDERLESS EDUCATIONAL STARTER KIT
Specifications
- breadboard dimensions: 80 x 60mm / 3.15″ x 2.36″
-
Ethernet shield for Arduino
Specifications
- data rates up to 10 Mbps
- integrated MAC controller
- 8 kB Transmit / Receive Packet Dual Port Buffer
- the MAC controller supports both Unicast, Multicast and Broadcast packets, has a programmable (up to 64-byte) pattern matching feature within a packet at user defined offset and programmable wake-up on multiple packet formats (Magic Packet, Unicast, Multicast, Broadcast, specific packet match or any packet)
- uses pin 10 and 2 on an Arduino UNO™ board. It also uses the ICSP connector as a serial connection to the shield to free up I/O pins
- dimensions: 68 x 53mm / 2.67 x 2.08″
-
UNIVERSAL TEMPERATURE SENSOR
Specifications
- range: -20° ~ +70°C
- output: 0 ~ 20mA current loop
- output voltage compliance: 10V
- accuracy: 2° full range
- one single adjustment
- 3-wire system: GND, +V and OUT
- power supply: 12VDC for 0 ~ 5V OUT / 15VDC for 0 ~ 10V OUT
- current consumption: 30mA max.
- dimensions: 55 x 35 x 15mm / 2.2 x 1.4 x 0.6″
-
10-CHANNEL 12 VDC LIGHT EFFECT GENERATOR
Specifications
- power supply: 12V DC
- consumption: max. 4A
- outputs: 12V DC / 400mA per channel (total : max 4A)
- dimensions: 140 x 100 x 27mm / 5.5 x 3.9 x 1.1″
-
1-CHANNEL USB STEPPER MOTOR CARD
Specifications
- power output: 750 mA continuous, (1 A peak)
- wide range AC – power input: 5 … 30 V
- 5 dry-contact inputs
- 1 logic open collector output
- power supply: 10 … 30 VAC
- dimensions: 117 x 65.5 x 25 mm / 4.6 x 2.58 x 0.98″
-
8-CHANNEL USB RELAY CARD
Specifications
- power supply for relays: 9-10Vac or 12 to 14Vdc (500mA), example: PS1205
- 8 high-power relays: 16A each (resistive load)
- dimensions: 160 x 107 x 30mm / 6.3 x 4.2 x 1.2″
-
15-CHANNEL IR RECEIVER
Specifications
- 15 open collector outputs: 50V / 100mA
- LED indication for every output
- change-over or pulse contact: selectable per output
- power supply: 8 – 14VDC or 2 x 12VAC / 150mA
- PCB dimensions: 70 x 145mm (2.8″ x 5.7″)
- recommended housing: WCAH2851: PLASTIC BOX – BLACK 160 x 95 x 55 mm
- recommended transformer: 2120038M
- recommended adapter: PS1205
-
IR REMOTE CONTROLLED DIMMER
Specifications
- max. load: 2A (4A with heat sink)
- supply voltage: 220VAC 50/60Hz (110VAC possible)
- transmitter / receiver distance: max. 7m (23′)
- not suitable for halogen lights
-
1-CHANNEL IR RECEIVER
Specifications
- transmitter / receiver range: up to 9m (29.5′)
- relay output: 240V / 5A (switch or pulse contact)
- supply voltage: 220VAC (110VAC possible)
- recommended housing: B6713
