“Complete kit with coaxial crimping tool and accessories, for perfect coaxial connections” already exists in your wishlist
Specifications
suitable for SD and SDHC cards
tested up to 32GB cards
supports ID3 TAG information: Title, Artist Name, Album Name and Year are displayed on the 2-line 16 char. PC1602WRS-KWA-E: LCD 16×2 STN Grey Positive Transflective WHITE Backlight
supports folders to one level deep
up to 1024 folders, each containing up to 16384 songs
equalizer settings: Flat , Loudness, Heavy, Clear, Soft, Disco, Live and Hall
decodes MP3 (MPEG 1.0 & 2.0 audio layer III (CBR, VBR, ABR), Till 320kbit/s. Fraunhofer IIS and Thomson licensed
amplifier: 2x 5Wrms @ 4ohm
power supply: 12Vdc/1A
dimensions: 132 x 62mm / 5.2 x 2.45″
Specifications
TRANSMITTER:
power supply: 3 AAA batteries (not incl.) (option: TR-G3/8)
433 MHz operation
8 digitally encoded channels
rubber keypad
LED function/mode indication
dimensions: 150 x58 x 23 mm
FCC approved ID code: NLO8058
RELAY RECEIVER CARD:
8 high-quality relay contacts, 5A/230Vac max.
relay outputs are transient suppressed using VDR’s
LED confirmation on each relay contact
input power: 12 Vac / 500 mA
Specifications
200W music power @ 4 ohm load
100Wrms power @ 4 ohm load
70Wrms power @ 8 ohm load
distortion: 0.02% @ 1KHz/10W
damping factor: >800
frequency response: 3Hz to 20KHz (-3dB)
sensitivity: 0.6Vrms
signal to noise ratio: 115dB
power supply: 25-30Vac 120VA
PCB dimensions: 107x62mm (approx.)
recommended power transformer:
230VAC input, 2 x 30VAC output: 12030
115 / 230VAC input, 2 x 25VAC output: TR8040 (output power reduced by ±15%)
Specifications
experiment module can be powered via USB
power output to target is supported
indicator LEDs for power supply and programming mode
dimensions:
programming and learning module: 90 x 74 mm / 3.54 x 2.91″
programmer only: 34 x 74 mm / 1.34 x 2.91″
Specifications
breadboard dimensions: 80 x 60mm / 3.15″ x 2.36″
Specifications
high contrast LCD: 64 x 128 pixels with white LED backlight
maximum sample rate: 1MS/s for repetitive signals, 100kS/s in real time
input amplifier bandwidth: 200kHz (-3 dB)
measurements can be performed up to: 100kHz
input impedance: 100kohm // 20pF
maximum input voltage: 30Vpeak (AC + DC)
input coupling: DC and AC
AD resolution: 8 bits
run modes: run, single
trigger level adjustable: in 16 steps
timebase range: in 15 steps, 10µs/division to 500ms/division
input sensitivity range: in 6 steps, 100mV/division to 5V/division
test output: 1.95kHz / 3.3Vpp
full auto set up for: Volt/div and time/div (or manual)
sensitivity down to 10mV
readouts: DC, AC+DC, true RMS, dBm, Vpp, min. & max.
time and voltage markers readout
frequency readout (through markers)
battery operated: 4 x AAA batteries (max. 100mA)
power save mode
dimensions: 80 x 115 x 40 mm / 3.14 x 4.52 x 1.57″
weight: 190g (6.70 oz) with batteries
Specifications
breadboard dimensions: 80 x 60mm / 3.15″ x 2.36″
Specifications
data rates up to 10 Mbps
integrated MAC controller
8 kB Transmit / Receive Packet Dual Port Buffer
the MAC controller supports both Unicast, Multicast and Broadcast packets, has a programmable (up to 64-byte) pattern matching feature within a packet at user defined offset and programmable wake-up on multiple packet formats (Magic Packet, Unicast, Multicast, Broadcast, specific packet match or any packet)
uses pin 10 and 2 on an Arduino UNO™ board. It also uses the ICSP connector as a serial connection to the shield to free up I/O pins
dimensions: 68 x 53mm / 2.67 x 2.08″
Specifications
range: -20° ~ +70°C
output: 0 ~ 20mA current loop
output voltage compliance: 10V
accuracy: 2° full range
one single adjustment
3-wire system: GND, +V and OUT
power supply: 12VDC for 0 ~ 5V OUT / 15VDC for 0 ~ 10V OUT
current consumption: 30mA max.
dimensions: 55 x 35 x 15mm / 2.2 x 1.4 x 0.6″
Specifications
power supply: 12V DC
consumption: max. 4A
outputs: 12V DC / 400mA per channel (total : max 4A)
dimensions: 140 x 100 x 27mm / 5.5 x 3.9 x 1.1″
Specifications
power output: 750 mA continuous, (1 A peak)
wide range AC – power input: 5 … 30 V
5 dry-contact inputs
1 logic open collector output
power supply: 10 … 30 VAC
dimensions: 117 x 65.5 x 25 mm / 4.6 x 2.58 x 0.98″
Specifications
power supply for relays: 9-10Vac or 12 to 14Vdc (500mA), example: PS1205
8 high-power relays: 16A each (resistive load)
dimensions: 160 x 107 x 30mm / 6.3 x 4.2 x 1.2″
