“Inspection mirror with telescopic Ø35mm” already exists in your wishlist
Specifications
suitable for SD and SDHC cards
tested up to 32GB cards
supports ID3 TAG information: Title, Artist Name, Album Name and Year are displayed on the 2-line 16 char. PC1602WRS-KWA-E: LCD 16×2 STN Grey Positive Transflective WHITE Backlight
supports folders to one level deep
up to 1024 folders, each containing up to 16384 songs
equalizer settings: Flat , Loudness, Heavy, Clear, Soft, Disco, Live and Hall
decodes MP3 (MPEG 1.0 & 2.0 audio layer III (CBR, VBR, ABR), Till 320kbit/s. Fraunhofer IIS and Thomson licensed
amplifier: 2x 5Wrms @ 4ohm
power supply: 12Vdc/1A
dimensions: 132 x 62mm / 5.2 x 2.45″
Specifications
TRANSMITTER:
power supply: 3 AAA batteries (not incl.) (option: TR-G3/8)
433 MHz operation
8 digitally encoded channels
rubber keypad
LED function/mode indication
dimensions: 150 x58 x 23 mm
FCC approved ID code: NLO8058
RELAY RECEIVER CARD:
8 high-quality relay contacts, 5A/230Vac max.
relay outputs are transient suppressed using VDR’s
LED confirmation on each relay contact
input power: 12 Vac / 500 mA
Specifications
200W music power @ 4 ohm load
100Wrms power @ 4 ohm load
70Wrms power @ 8 ohm load
distortion: 0.02% @ 1KHz/10W
damping factor: >800
frequency response: 3Hz to 20KHz (-3dB)
sensitivity: 0.6Vrms
signal to noise ratio: 115dB
power supply: 25-30Vac 120VA
PCB dimensions: 107x62mm (approx.)
recommended power transformer:
230VAC input, 2 x 30VAC output: 12030
115 / 230VAC input, 2 x 25VAC output: TR8040 (output power reduced by ±15%)
Specifications
experiment module can be powered via USB
power output to target is supported
indicator LEDs for power supply and programming mode
dimensions:
programming and learning module: 90 x 74 mm / 3.54 x 2.91″
programmer only: 34 x 74 mm / 1.34 x 2.91″
Specifications
breadboard dimensions: 80 x 60mm / 3.15″ x 2.36″
Specifications
high contrast LCD: 64 x 128 pixels with white LED backlight
maximum sample rate: 1MS/s for repetitive signals, 100kS/s in real time
input amplifier bandwidth: 200kHz (-3 dB)
measurements can be performed up to: 100kHz
input impedance: 100kohm // 20pF
maximum input voltage: 30Vpeak (AC + DC)
input coupling: DC and AC
AD resolution: 8 bits
run modes: run, single
trigger level adjustable: in 16 steps
timebase range: in 15 steps, 10µs/division to 500ms/division
input sensitivity range: in 6 steps, 100mV/division to 5V/division
test output: 1.95kHz / 3.3Vpp
full auto set up for: Volt/div and time/div (or manual)
sensitivity down to 10mV
readouts: DC, AC+DC, true RMS, dBm, Vpp, min. & max.
time and voltage markers readout
frequency readout (through markers)
battery operated: 4 x AAA batteries (max. 100mA)
power save mode
dimensions: 80 x 115 x 40 mm / 3.14 x 4.52 x 1.57″
weight: 190g (6.70 oz) with batteries
Specifications
breadboard dimensions: 80 x 60mm / 3.15″ x 2.36″
Specifications
data rates up to 10 Mbps
integrated MAC controller
8 kB Transmit / Receive Packet Dual Port Buffer
the MAC controller supports both Unicast, Multicast and Broadcast packets, has a programmable (up to 64-byte) pattern matching feature within a packet at user defined offset and programmable wake-up on multiple packet formats (Magic Packet, Unicast, Multicast, Broadcast, specific packet match or any packet)
uses pin 10 and 2 on an Arduino UNO™ board. It also uses the ICSP connector as a serial connection to the shield to free up I/O pins
dimensions: 68 x 53mm / 2.67 x 2.08″
Specifications
range: -20° ~ +70°C
output: 0 ~ 20mA current loop
output voltage compliance: 10V
accuracy: 2° full range
one single adjustment
3-wire system: GND, +V and OUT
power supply: 12VDC for 0 ~ 5V OUT / 15VDC for 0 ~ 10V OUT
current consumption: 30mA max.
dimensions: 55 x 35 x 15mm / 2.2 x 1.4 x 0.6″
Specifications
power supply: 12V DC
consumption: max. 4A
outputs: 12V DC / 400mA per channel (total : max 4A)
dimensions: 140 x 100 x 27mm / 5.5 x 3.9 x 1.1″
Specifications
power output: 750 mA continuous, (1 A peak)
wide range AC – power input: 5 … 30 V
5 dry-contact inputs
1 logic open collector output
power supply: 10 … 30 VAC
dimensions: 117 x 65.5 x 25 mm / 4.6 x 2.58 x 0.98″
Specifications
power supply for relays: 9-10Vac or 12 to 14Vdc (500mA), example: PS1205
8 high-power relays: 16A each (resistive load)
dimensions: 160 x 107 x 30mm / 6.3 x 4.2 x 1.2″
