“Inspection mirror with telescopic Ø35mm” already exists in your wishlist
Specifications
experiment module can be powered via USB
power output to target is supported
indicator LEDs for power supply and programming mode
dimensions:
programming and learning module: 90 x 74 mm / 3.54 x 2.91″
programmer only: 34 x 74 mm / 1.34 x 2.91″
Specifications
breadboard dimensions: 80 x 60mm / 3.15″ x 2.36″
Specifications
high contrast LCD: 64 x 128 pixels with white LED backlight
maximum sample rate: 1MS/s for repetitive signals, 100kS/s in real time
input amplifier bandwidth: 200kHz (-3 dB)
measurements can be performed up to: 100kHz
input impedance: 100kohm // 20pF
maximum input voltage: 30Vpeak (AC + DC)
input coupling: DC and AC
AD resolution: 8 bits
run modes: run, single
trigger level adjustable: in 16 steps
timebase range: in 15 steps, 10µs/division to 500ms/division
input sensitivity range: in 6 steps, 100mV/division to 5V/division
test output: 1.95kHz / 3.3Vpp
full auto set up for: Volt/div and time/div (or manual)
sensitivity down to 10mV
readouts: DC, AC+DC, true RMS, dBm, Vpp, min. & max.
time and voltage markers readout
frequency readout (through markers)
battery operated: 4 x AAA batteries (max. 100mA)
power save mode
dimensions: 80 x 115 x 40 mm / 3.14 x 4.52 x 1.57″
weight: 190g (6.70 oz) with batteries
Specifications
breadboard dimensions: 80 x 60mm / 3.15″ x 2.36″
Specifications
data rates up to 10 Mbps
integrated MAC controller
8 kB Transmit / Receive Packet Dual Port Buffer
the MAC controller supports both Unicast, Multicast and Broadcast packets, has a programmable (up to 64-byte) pattern matching feature within a packet at user defined offset and programmable wake-up on multiple packet formats (Magic Packet, Unicast, Multicast, Broadcast, specific packet match or any packet)
uses pin 10 and 2 on an Arduino UNO™ board. It also uses the ICSP connector as a serial connection to the shield to free up I/O pins
dimensions: 68 x 53mm / 2.67 x 2.08″
Specifications
range: -20° ~ +70°C
output: 0 ~ 20mA current loop
output voltage compliance: 10V
accuracy: 2° full range
one single adjustment
3-wire system: GND, +V and OUT
power supply: 12VDC for 0 ~ 5V OUT / 15VDC for 0 ~ 10V OUT
current consumption: 30mA max.
dimensions: 55 x 35 x 15mm / 2.2 x 1.4 x 0.6″
Specifications
power supply: 12V DC
consumption: max. 4A
outputs: 12V DC / 400mA per channel (total : max 4A)
dimensions: 140 x 100 x 27mm / 5.5 x 3.9 x 1.1″
Specifications
power output: 750 mA continuous, (1 A peak)
wide range AC – power input: 5 … 30 V
5 dry-contact inputs
1 logic open collector output
power supply: 10 … 30 VAC
dimensions: 117 x 65.5 x 25 mm / 4.6 x 2.58 x 0.98″
Specifications
power supply for relays: 9-10Vac or 12 to 14Vdc (500mA), example: PS1205
8 high-power relays: 16A each (resistive load)
dimensions: 160 x 107 x 30mm / 6.3 x 4.2 x 1.2″
Specifications
15 open collector outputs: 50V / 100mA
LED indication for every output
change-over or pulse contact: selectable per output
power supply: 8 – 14VDC or 2 x 12VAC / 150mA
PCB dimensions: 70 x 145mm (2.8″ x 5.7″)
recommended housing: WCAH2851: PLASTIC BOX – BLACK 160 x 95 x 55 mm
recommended transformer: 2120038M
recommended adapter: PS1205
Specifications
max. load: 2A (4A with heat sink)
supply voltage: 220VAC 50/60Hz (110VAC possible)
transmitter / receiver distance: max. 7m (23′)
not suitable for halogen lights
Specifications
transmitter / receiver range: up to 9m (29.5′)
relay output: 240V / 5A (switch or pulse contact)
supply voltage: 220VAC (110VAC possible)
recommended housing: B6713
